KME Perforated Copper Sheet TECU® PATINA, Perforated RV Round Offset

Processing

• The surfaces of TECU® Patina panels are finished at the factory and must be treated with special care.
• Do not process TECU® patina boards in the rain.
• In general: do not mechanically stress wet TECU® patina boards (e.g. do not walk on them or use them as storage areas).
• TECU® Patina panels must not be torn off.
• Due to the amount of dust generated when processing large quantities of TECU® Patina indoors, wear a light protective mask.
• After processing TECU® Patina, the machines and tools must be cleaned.
• Observe the constraint-free installation of the TECU® Patina panels and elements.
• For a uniform or uniform appearance, the rolling direction of the TECU® Patina surface must be taken into account as the direction of installation.
• When installing TECU® Patina panels with directly visible fastening, KME recommends trimming the panels on all sides to 900x2800mm, as the edges may have possible discoloration due to production.

DIN EN 988 (Standard), Edition: 1996-08 Zinc and zinc alloys - Requirements for rolled flat products for the construction industry; German version EN 988:1996

DIN EN 1999-1-4/A1 (Standard), Edition: 2011-11 Eurocode 9: Design and construction of aluminium structures - Part 1-4: Cold-formed profiled sheets; German version EN 1999-1-4:2007/A1:2011

DIN EN 1999-1-1, date of issue: 2014-03 Eurocode 9: Design and construction of aluminium structures - Part 1-1: General design rules; German version EN 1999-1-1:2007 + A1:2009 + A2:2013

DIN EN 1999-1-1/NA/A1, date of issue: 2014-06 National Annex - Nationally determined parameters - Eurocode 9: Design and construction of aluminium structures - Part 1-1: General design rules; Amendment 1

DIN EN 1999-1-1/NA/A2, date of issue: 2015-03 National Annex - Nationally defined parameters - Eurocode 9: Design and construction of aluminium structures - Part 1-1: General design rules; Amendment A2 DIN EN 12810-1 (Standard), Edition: 2004-03 Façade scaffolding made of prefabricated components - Part 1: Product specifications; German version EN 12810-1:2003

DIN EN 14509, Edition: 2013-12 Self-supporting sandwich panels with metal cover layers on both sides - Factory manufactured products - Specifications

DIN EN 14782 (Standard), Edition: 2006-03 Self-supporting roofing and wall cladding elements for interior and exterior use made of sheet metal - Product specification and requirements; German version EN 14782:2006

DIN EN 14783 (Standard), Edition: 2006-12 Full-surface supported roofing and wall cladding elements for indoor and outdoor use made of sheet metal - Product specification and requirements; German version EN 14783:2006

DIN 18360 (Standard), Edition: 2012-09 VOB Procurement and Contract Regulations for Construction Services - Part C: General Technical Contract Conditions for Construction Services (ATV) - Metal Construction Works

DIN 18351 (Standard), Edition: 2015-08 VOB Procurement and Contract Regulations for Construction Services - Part C: General Technical Contract Conditions for Construction Services (ATV) - Rear-ventilated facades

DIN 18516-1 (Standard), Edition: 2010-06 Exterior wall cladding, rear-ventilated - Part 1: Requirements, Test Principles

DIN 24041 (Standard), Edition: 2002-12 Perforated Panels - Dimensions

• Width 500-1000 mm
• Tensile strength 240-285 N/mm²
• Yield strength 180-230 N/mm²
• Elongation at break min. 15%
• Hardness max. 90
• Density 8.93 g/cm³

[...] For detailed information, see product data sheet