blaugelb Protect

The necessary fastening points of the building elements and their distance from each other are based on the general installation guidelines (e.g. current RAL "Guidelines for Installation Chapter 5"), taking into account the window weights and any additional loads to be expected.

The blaugelb Protect fastening system lies flat against the window reveal, so that high, horizontal and vertical forces can be transferred to the anchoring base. blaugelb Protect is an invisible fastening when the sash is open and can even be pre-installed at the factory. The variable hole pattern enables fastening in accordance with the rules with the necessary edge distance to the loaded edge of the anchoring base. This screw connection can be carried out either with a blaugelb frame fixed screw or a fastener approved by the building authorities.

The system-integrated, rotatable adjustment screw flexibly adapts the position of the window and thus the mounting joint width to the actual construction situation.

The extensive tests document that blaugelb Protect also meets the requirements of safety-relevant attachment points (e.g. for fall-resistant components ETB guideline "Components that protect against falls"). There is a safe load transfer to the anchoring base.

After hooking in the element wings, it is possible to readjust to the millimetre (if necessary) on any blaugelb Protect. The sealing of the window or door elements is not obstructed and can be freely selected according to the respective installation situation. The combination with multifunctional hinges is also possible, because the typical spacer block can be dispensed with on the sides without risking loss of load-bearing capacity.

Tested properties:

• Fall protection according to AbP
• Fall protection according to ETB guideline
• "Components that protect against falling"
• horizontal design values of the resistance
horizontal
• load, design value of the resistance
• FH a-i, Rd = (from the outside to the inside from wind suction, railing loads)
• FH i-a, Rd = (from the inside to the outside from wind suction, railing loads)
• Proof of suitability for RC2 provided
• Vertical load application

Product advantages:

• with an offset screw, the blaugelb Protect can also be used turned outwards
• Convenient adjustment and secure fastening Adjustable
• for the fastening of RC 2 tested elements
• , thus variable in the joint widths
• Permanent serviceability of the fastening
Secure
• fastening even with high element weights
• Rule-compliant displacement of the fastening plane from the endangered edge area of the anchoring base
• Perfect for combination with multifunctional hinges No
• lateral spacers necessary
• for the fastening of fall-protection elements Tested invisible
• fastening when the sash is open
Ideal
• fastening for fixed glazed building elements (without glazing)
• Perforation optionally for fixed frame screw or for dowel system assembly
,
• can be pre-assembled at the factory
,
• can be used up to a free dowel length of 45 mm
• , static design resistors, suction/pressure
• , vertical load application

Material: white galvanized strip steel

Dimensions: 2.5 x 30 x 100 mm, 2.5 x 30 x 150 mm, 2.5 x 30 x 220 mm, 2.5 x 30 x 280 mm

Hole Ø: 8.05 mm for fastening with blue-yellow fixed frame screws FK-T30, 10.5 mm for fastening with a dowel system Ø 10 mm

Elongated hole length: 25 mm

Adjustment screw: integrated, swivel bearing, 7.5 x 35/50/70/90 mm T30, white zinc plated with pressed-on hexagon nut

Adjustment: via pressed-on hexagon nut with blue-yellow Mounting key SW 13 mm (not included)

Fastening in the structure: blue-yellow fixed frame screw FK-T30 x L or dowel system Ø 10 mm

Pre-hole in the frame: Ø 5 mm blind hole, facing

the mounting jointReinforcement in the frame (plastic): at least 1.5 mm, screwing of the reinforcement according to profile system specifications