Teckentrup roller shutter 4020 made of aluminium profiles

Teckentrup GmbH & Co. KG

Description

Our double-walled, insulated roller shutter 4020 is made of aluminium profiles. It is equipped with a camber seal and a primed winding shaft. The drive is a slip-on drive with 400 V three-phase current. An emergency hand crank and an integrated safety gear are included as standard. The roller shutter profile 4020 in a coil-coated design is particularly suitable for use near the sea (corrosion) or in agricultural environments (stables). Even in relatively aggressive (e.g. chemical) environments, the aluminium profile 4020 is more corrosion-resistant than galvanised steel.

B<a href="https://www.teckentrup.biz/fileadmin/user_upload/teckentrup/Downloadcenter/01_Broschueren_DE/Broschuere_Rolltore.pdf" target="_blank">roschüre

More Over


Product features:
  • Double-walled, insulated from aluminium
  • Surface variety
  • With lintel seal and primed winding shaft
Installation in:

  • Masonry: min. 120 mm
  • Concrete: min. 150 mm
  • Steel
  • Aerated concrete: min. 200 mm (only with steel edging)
  • Wood: min. 240 mm

Course text

Technical Information

Performance characteristics (according to EN 13241-1):

Double-walled aluminium profiles:

  • Thermal insulation
  • U-value according to EN ISO 12567-1 (for door size = 4000 x 4000 mm)
  • U-value W/(m²*K) (complete door): 3.5 W/(m²*K)
  • Sound insulation value
  • RW (tested) 20 dB
  • Air permeability
  • Classification according to EN 12426 Class: 0
  • Wind load
  • Classification according to EN 12424 Class: 2
  • Driving rain tightness
  • Testing according to EN 12489
  • Classification according to EN 12425 Class: 0
Size range:
  • Construction guideline dimensions: Width: 1000 to 11,500 mm

Height: 1000 to 12,000 mm

Doors up to 15,000 mm in wind load class 2

Doors up to 18,000 mm Door width in wind load class 1 available on request

Gate armour:

Consisting of hinge-like interlocking aluminium profiles

Surface:
  • Aluminum stucco design
  • Aluminum
  • strip-coated
drives:
  • Slip-on drive with integrated safety gear or chain drive with separate safety gear and electrical forced disconnection
  • Three-phase voltage 400 V, 50 Hz, 60 % ED, protection class IP 54, with emergency hand crank, TÜV tested.
  • Other special voltages, degrees of protection or emergency actuations on request
Control:
  • For plug-on and chain drives, pre-wired ready for plugging and designed with CEE plug in the basic equipment and as a dead man's control , is easily upgradeable with:
  • Self-holding "CLOSED" in conjunction with a closing edge protection
  • Radio remote control Automatic
  • inlet (with traffic lights)
  • Accessories for controls:
  • Automatic inlet (with traffic lights), additional light barrier recommended
  • Traffic light control
  • Digital induction loop
  • without closing edge protection:
  • In the basic version, control voltage 24 V safety extra-low voltage, protection class IP 65, "gate closed" in dead man's switch (continuous pressure), push buttons "open-stop-closed"
  • with closing edge protection:
  • control with self-monitoring closing edge protection, control voltage 24 V safety extra-low voltage, protection class IP 65, "gate closed" and "gate open" in self-holding with push buttons" Optional
extras:
  • Fixed side panel with built-in door
  • Swivel side panel with built-in door
  • Armour cladding made of:
  • Galvanised sheet aluminium
  • ,
  • natural
  • Other
  • designs on request:
  • Slanted floor profiles, adapted to the floor
  • Side or roof mounts

Downloads